When it comes to choosing your arduino pro micro case, there are hundreds of different choices. In our review, weve considered all the various features youll need to know before buying the best arduino pro micro case. We hope that through this article, with our comparison table, in-detail review of each product can help you decide which one is your best arduino pro micro case.
Best arduino pro micro case
1. ELEGOO UNO Project Super Starter Kit with Tutorial and UNO R3 Compatible with Arduino IDE
FeatureFree PDF tutorial(more than 22 lessons) and clear listing in a nice package
The most economical way to starting Arduino programming for those beginners who are interested
Lcd1602 module with pin header (not need to be soldered by yourself)
This is the upgraded starter kits with power supply module, 9V battery with dc
High quality kite with uno R3, 100 percent compatible with Arduino uno R3
Elegoo Inc. is a professional manufacturer and exporter that is concerned with the design, development production and marketing of arduino, 3d printers, raspberry pi and STM32.
Our Dream is to make the best price and best quality produce for customers.
So we would like to receive your valuable suggestions for our products and we can improve them for you.
1pcs UNO R3 Controller Board
1pcs LCD1602 Module ( with pin header)
1pcs Breadboard Expansion Board
1pcs Power Supply Module WARNING: Pls. do not use the voltage higher than 9V
1pcs Joystick Module
1pcs IR Receiver
1pcs Servo Motor (SG90)
1pcs Stepper Motor
1pcs ULN2003 Stepper Motor Driver Board
1pcs Ultrasonic Sensor
1pcs DHT11 Temperature and Humidity Module
1pcs 9V Battery with DC
1pcs 65 Jumper Wire
1pcs USB Cable
1pcs Active Buzzer
1pcs Passive Buzzer
1pcs 5V Relay
1pcs Tilt Switch
5pcs Button (small)
1pcs 1 digit 7-segment Display
1pcs 4 digit 7-segment Display
5pcs Yellow LED
5pcs Blue LED
5pcs Green LED
5pcs Red LED
1pcs RGB LED
2pcs Diode Rectifier (1N4007)
2pcs NPN Transistor (PN2222)
1pcs IC 74HC595
10pcs Female-to-male Dupont Wire
2. Emakefun Nano V3.0, Nano Board ATmega328P 5V 16M Micro-Controller Board with USB Cable for Arduino (Pre-soldered Nano 5pcs)
FeatureCH340G Replace FT232RL,so pls. use the driver from this link:https://github.com/emakefun/emakefun-nano-kit
TheUpgradedEmakefun Nano is a small, complete, breadboard-friendly andhigh qualityboard based on the Atmega328P-AU MCU.Adopting Immersion Gold Technology. Support ISP download, USB download and USB Power
No Soldering needed.TheUpgradedEmakefun Nano improved the design of PCB to solve the issue that the pins of Nano can't fit to breadboard perfectly. When you use our upgraded Nano, you will find the Pins arealigned nicely with the holes of breadborad
Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. We use high quality PCB original material and iproved produce technology to make sure every board has smooth edge and more reliable quality
It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). Follow this link:https://github.com/emakefun/emakefun-nano-kit/blob/master/Resume_Arduino_BootLoader.pdf, you can easily solve the problem that the nano board cannot download the program when it is connected to the computer.
DescriptionSpecification: CH340G Replace FT232RL. Operating Voltage(logic level): 5V. 8 analog inputs ports:A0 ~ A7. 14 Digital input / output ports:TX,RX,D2 ~ D13. 6 PWM ports:D3, D5, D6, D9, D10, D11. 1 pairs of TTL level serial transceiver ports RX / TX. Support USB download and Power. Support for external 5V ~ 12V DC power supply. Support power supply by 9V battery. Support ISP download. Package including: 5 x Arduino Nano V3.0 with ATMEGA328P Module (welded) 1 x USB Cable
3. XCSOURCE 5pc Pro Mini Enhancement ATMEGA328P 16MHz 5V Compatible Arduino PRO Module TE362
FeatureATmega328 running at 16MHz with external resonator
USB connection off board
Max 150mA output
Over current protected
ATmega328 running at 16MHz with external resonator (0.5% tolerance)
USB connection off board
Max 150mA output
Over current protected
Reverse polarity protected
DC input 5V up to 12V
On board Power and Status LEDs
5x Pro Mini Enhancement ATMEGA328P 16MHz 5V Compatible Arduino PRO Module
4. for Arduino Nano V3.0, ELEGOO Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable)
FeatureYou could download the driver of Elegoo Nano V3.0 at: http://bit.ly/2jKlJMO
The Nano is using the chips ATmega328P and CH340, not FT232 as official Arduino, so pls. use the driver from above link.
It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper.
Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other).
The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
5. SunFounder R3 Case Enclosure New Transparent Gloss Acrylic Computer Box Compatible with Arduino R3
FeatureProtective case for Arduino R3
The R3 case is made by high grade acrylic
Fastened by eight screws, easy to install and secure
Unique design for Arduino R3 with pin leakage, which provides easy connection to other components
Provides excellent protection, with fashion appearance
6. TowerPro SG92R Micro Servo - 2 pack
FeatureAuthentic Tower Pro Micro Servo - Weight: 9g
Stall torque: 2.5kg /cm(4.8v)
Lightweight and Smooth Carbon Fiber Gears - Five times more strength than nylon gears
Dimensions: 2312.2x27mm - Operating Voltage: 4.8 VDC
We are a Tower Pro GOLDEN Dealer - Buy the Genuine OEM Servos
7. Gikfun FT232RL 3.3V 5.5V FTDI Mini USB to TTL Serial Converter Adapter Module DIY Kit for Arduino Mini Port (Pack of 2pcs) AE1186x2_1
FeatureSupport 3.3V, 5V, chipset FT232RL, Pin definition: DTR,RXD,TX,VCC,CTS,GND
Please dl the file from links: http://www.ftdichip.com/FTDrivers.htm
USB power has over current protection, using 500MA self-restore fuse
RXD/TXD transceiver communication indicator
8. SING F LTD 2X Pro Micro Compatible with Arduino Atmega32U4 5V 16Mhz Compatible Board Free Pins
FeatureThe Pro Micro is similar to the Pro mini except with an ATmega32U4 on board.
The Micro-USB connector on board is for programming.
This tiny little board does all of the neat-o Arduino tricks that you're familiar with: 4 channels of 10-bit ADC, 5 PWM pins, 12 DIOs as well as hardware serial connections Rx and Tx.
Running at 16MHz and 5V, this board will remind you a lot of your other favorite Arduino-compatible boards, but this little guy can go just about anywhere.
Supported under Arduino IDE v1.0.1.
9. Pro Micro ATmega32U4 5V 16MHz Micro-USB Development Module Board with 2 Row pin Header Compatible arduino Leonardo Replace ATmega328 Pro Mini
FeatureATMega 32U4 running at 5V/16MHz
Supported under Arduino IDE v1.0.1
On-Board micro-USB connector for programming
4 x 10-bit ADC pins
12 x Digital I/Os
10. Emakefun Development Board, Development Board for Arduino R3 with Micro Interface and BLE Wireless Module,Base on ATmega328P for Project
FeatureBluetooth moduleWirelessly connect your phone via APP
Micro interfaceYou can use the data cable of your phone connect with computer
ChipATmega328Psame as the official version
QualitySolder is Very Clean
ServiceAll materials downloaded from(https://github.com/emakefun/emakefun-Ble-uno)